Piezoelectric Sensors and Transducers in Your PCB

May 6, 2019 Cadence PCB Solutions

Ultrasonic transducer on blue background


From battery-powered wrist watches to electric cigarette lighters, piezoelectric elements play an important role in many devices, especially as a clock in digital circuits. All sensors for use in electronic systems have a common characteristic: they take some type of physical disturbance and convert it into an electrical signal. As technology progresses, more sophisticated sensors are being developed for a variety of measurements, but piezoelectric sensors and transducers are here to stay.

Piezoelectric Sensors and Transducers

With the exception of optical measurements, many dynamic measurements are gathered by examining the output from a piezoelectric sensor. These sensors are rugged and can withstand very high temperatures while remaining very sensitive to changes in environmental variables. They are also manufactured in a variety of sizes, making them suitable for mounting on a PCB or as a packaged unit that attaches to a board with copper wire.

In the simplest sense, a piezoelectric material used as a sensor converts an applied mechanical load to an electric field, which can then be measured as a voltage. This voltage can then be converted to digital data with an analog-digital converter (ADC) on your board. You can then use the equivalent digital number to perform some calculations and determine some physical quantity.

In the case of an oscillating mechanical vibration, the output voltage also oscillates at the same frequency as the mechanical vibration. One important point here is that any vibrating mechanical membrane, which includes a piezoelectric crystal, has a spectrum of natural frequencies, not just a single resonance.

Furthermore, the equivalent electronic circuit formed by a piezoelectric element has multiple resonance and antiresonance frequencies. If you want to use a piezoelectric element as a transducer in your board, it can be excited at multiple resonance frequencies.

When a mechanical load is applied to the element, the frequencies in the response spectrum will shift to different values, and the magnitude of this shift is proportional to the applied load. This change in resonance is used to gather very sensitive biological and chemical measurements as the change in the vibration amplitude will be extremely sensitive near resonance.

When working with a piezoelectric transducer, you will need to take this frequency response into account. Changing the frequency of an input AC signal at a constant voltage will eventually cause the acoustic vibration of the transducer to change nonlinearly as you near a resonance or antiresonance. For this reason, you should be mindful of the frequency response if you want your transducer to respond in the linear regime.


Sensors and transducers on a blue PCB

Utilizing sensors and transducers properly in your designs can be beneficial for device accuracy



Placing Piezoelectric Elements on Your PCB

The first point to make here is in choosing the right type of piezoelectric element for use in your device. Ceramic piezoelectric elements have lower costs and have sensitivities that can reach two orders of magnitude higher than piezoelectric crystals (i.e., quartz), but their sensitivity degrades over time, especially at higher temperature. Crystals have much better long-term stability and are a better choice for high temperature measurements.

If you want to use a piezoelectric transducer to measure vibrations at a specific frequency, you should try to select a piezoelectric transducer with a resonance that matches the particular frequency you wish to measure. You can then use a bandpass filter in your board to remove responses at other frequencies.

If you are measuring across a range of frequencies, the usable range will lie between the first antiresonance and the first resonance. You should use a high pass filter with cutoff near the first antiresonance (which has a lower frequency) and a low pass filter with cutoff near the first resonance to control the response range. The response from this sensor will have good linearity to changes in load, while it will be flat to changes in applied frequency for a constant load. This allows the two quantities to be easily separated during measurement.

Just like the placement of a quartz crystal oscillator for generating clock signals, you should avoid placing the piezoelectric element itself directly above a ground plane as this creates a center-fed patch antenna. This increases susceptibility to EMI, especially at the ground plane’s resonance frequency. Piezoelectric sensors are generally connected to an amplifier, so any noise present in the transducer output will also be amplified; you should try to clean up these signals as much as possible. Some circuit designers will use sequential high and low pass filtering to tailor their passband to just the right frequency range.


Quartz oscillators on white background

Quartz oscillators: one common piezoelectric device


Finally, the output impedance from piezoelectric elements is very high (usually 1 MOhm), so an impedance matching circuit should be used at the load in order to maximize power transfer into/out of the element. There are several options for matching your source and load impedance, one being linear two-port matching network. Some examples can be found in the research literature.

Piezoelectric elements also have internal dielectric losses, i.e., the electrical signal is dissipated as heat. With crystals, dielectric losses are low, so thermal management is less of a concern. For ceramics, dielectric losses are much higher, so designers should use some form of thermal management, like a thermal pad or heat sink.

Using the right PCB layout and design software with a full suite of design tools and extensive component libraries allows you to design boards to control and collect data from a variety of sensors and transducers. Allegro PCB Designer contains the tools you need to design boards for gathering sensor data and much more.

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Tips for Creating the Best PCB Layer Stackup
Tips for Creating the Best PCB Layer Stackup

Before you place that first part or route that first trace, make sure that your PCB layer stackup is set up...

Next Article
What is a Ground Loop and How to Minimize its Harmful Consequences
What is a Ground Loop and How to Minimize its Harmful Consequences

Working through unexpected return current problems from your ground loop can be a reality addressed during ...