The Importance of Dynamic Load Line Analysis

November 20, 2019 Cadence PCB Solutions

An overheated transistor on a printed circuit board

 

In life, the daily variables are nearly limitless. Although you find a routine that suits your immediate needs at the time, it is usually only temporary. We do not have the luxury of an analysis system that we could use to plot the optimum balance between life and work.

We, as adults, could undoubtedly use a plotted guideline (load line) that allows us to know the exact point where our (loads) life, work, and financial responsibility intersects for that perfect balance.

Unlike electronics, we do not have a characteristic curve, but then again, electronics need it more than we do. Because the ability to analyze and plot the optimum operating point for a device or component is critical to the design process. Besides, the electronics are not trying to keep up with the Jones’, so it is much easier to determine their load line.

What is a Load Line?

In the graphical analysis of (nonlinear) electronic circuits, a load line is a line drawn on the characteristic curve. Furthermore, a characteristic curve is a graph of the current in comparison to the voltage in a nonlinear device or component, such as a transistor or diode.

A load line represents the constraint put on the voltage and the current in a nonlinear device by the external circuit. It is usually drawn as a straight line on the graph of the current and voltage comparison. In summary, the load line represents the response of the linear part of the circuit, connected to the nonlinear device in question.

Also, the points where the load line and the characteristic curve intersect are the possible operating point(s) or Q points of the circuit. This also means that at these points, the current and voltage parameters of both parts of the circuit match (optimal).

Types of Load Lines

In general, semiconductor circuits usually have both DC and AC currents in them, with a source of DC to bias the nonlinear semiconductor to the correct operating point, with the AC signal superimposed on the DC. In terms of load lines, you can use them separately for both the AC and DC load line analysis.

The DC load line is the load line of the DC equivalent circuit and is defined by reducing the reactive components to zero, by replacing the capacitors with open circuits and inductors with short circuits. In summary, the DC load line is used to determine the correct DC operating point, often called the quiescent point or Q point.

Upon defining the Q point for DC, you can now draw an AC load line through the Q point. Also, the AC load line is a straight line with a slope equal to the AC impedance facing the nonlinear device, which, in general, is different from the DC resistance. Furthermore, the AC load line represents the ratio of AC voltage to current in the device in question. Finally, the slope of the AC load line depends on the frequency of the applied signal, because the resistance of the reactive components will vary with frequency.

Static and Dynamic Load Lines

The term static, whether referring to an IP address or a load line in electronics, is synonymous with the concept of constant.

Whereas the same is true of the term dynamic when you refer to it as the concept of continuous change or fluctuation.

Thus, we use the dynamic load line to plot the dynamic I-V (current-voltage) trajectory on a rectangular graph. In general, the dynamic load line measurement is used in conjunction with the I-V Curve measurement.

Large density of components on a printed circuit board

Your power supply can affect any number of components on your board.

 

The Quiescent Point of Transistors

There are DC and AC load lines on an amplifier transistor. Furthermore, the DC load line ultimately depends on the resistivity drop to position the Q point in the middle of the linear area. Whereas the dynamic load line depends on the AC resistivity seen by the transistor through the load transformer or the coupling capacitor.

Overall, the two load lines are quite different, and the Q point should be set to allow a full power range for the dynamic load line without passing through the maximum dissipation of the amplifier. In other words, this is the point of amplification where the signal obtains complete amplification without any attenuation. Also, this is located when the transistor operates in the active zone.

In summary, during the operation of a transistor as an amplifier, you can choose its operating point somewhere well within the active zone of its characteristics curve. However, when you use dc load line analysis to determine it, it will be the most optimized position of Q point.

The Importance of (Dynamic) Load Line Analysis

In the field of electronics, we are always in need of parameters, limits, and tolerances. Without them, we would not be able to design and manufacture PCBs or electronic devices accurately.

The need for load line analysis is no different, and its requirement is no less critical. The word optimal is by in large the goal of all designs and product manufacturing. The attempt to achieve anything less is not acceptable according to the demands of consumers for greater product functionality.

The very essence of the dynamic load line analysis is to achieve the optimal operating level regardless of input, duration of use, or load placed on the device in question. Therefore, the importance of obtaining this information is paramount. The overall quality of your design itself is dependent on this information being accurate, or you risk performance issues or exceeding operating parameters.

 

Microchip transistor being tested in an engineering environment

Working with both AC and DC currents can be particularly challenging in power supply design

 

Dynamic load line analysis provides the designer with the proper operating point for a particular component. The need for this information to be accurate is essential to one’s overall design. It also affects the overall functionality of the component, the electronic circuit, and even the device itself.

Optimizing dynamic load line analysis for your designers and production teams comes along with Cadence’s suite of design and analysis tools. If you’re considering looking into dynamic load line analysis and other nonlinear circuit elements, Allegro PCB Designer can unquestionably provide the implementation you need into your PCB designs. 

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
The Importance of Component Tolerance Modeling in PCB Design
The Importance of Component Tolerance Modeling in PCB Design

Component tolerance modeling is an invaluable design insight tool that reduces cost as well as build times....

Next Article
The Benefits and Advantages of Frequency Response Simulation in PCB Design
The Benefits and Advantages of Frequency Response Simulation in PCB Design

Frequency response simulation is a vital design tool that offers greater insight into the frequency design ...

Start My Free Trial Today

Start Now