Types of Diode and Determining the Operating Point of a Diode

September 17, 2019 Cadence PCB Solutions

Various types and shapes of diodes

 

I used to fancy myself a fairly good athlete during my teen years. After all, I started on the football team and even played both offense and defense for a while. Although, a little short for basketball, I could shoot pretty well. I probably did not give baseball enough of a chance, but I could run and catch. The one thing about baseball that I never really mastered was to always use the web instead of my palm. Not catching the ball in that sweet spot could be quite painful.

Many electrical components also have what you could call a sweet spot or a preferred operating point or range. One such component is the diode. Diodes come in many types, sizes and shapes; however, they can typically be viewed as switches. That is, for the right electrical conditions they are on; otherwise, they are off. And in many applications, it is very important to know precisely where the operating point of a diode is for your application. Let’s review some of the common types of diodes and then see how we can accurately determine where the operating point lies.

Types of Diode

Believe it or not, the principles for the operation of diodes has been known since the late 1800s. In fact, the thermionic diode, patented by John Ambrose Fleming in 1904, was the first vacuum tube, which was the primary device for radio communications and other electrical devices until the invention of the transistor. 

The simplest diodes are comprised of p-type and n-type materials that form a PN junction across which electrons flow when sufficient charge is present across the device. This condition is generally referred to as forward-biased. When there is no current flow through the diode, it is referred to as reverse-biased. This type of diode is commonly used for rectification or conversion of an ac signal to dc, as shown below.

 

Bridge rectifier circuit

Four diode bridge rectifier

 

Today, there are dozens of diode types that are used in all types of electrical and electronic circuits. Some of these are listed below:

Types of Diodes:

  • Zener diode - used for voltage regulation.

  • Schottky diode - used as rectifiers in high-frequency circuits.

  • Varactor diode - functions as a variable capacitor. 

  • Avalanche diode - used for RF and microwave generation.

  • Silicon Controlled Rectifier (SCR) - used as controllers. For example, to set duty cycles. 

  • Schockley diode - used as a trigger switch for SCRs.

  • PIN diode - used as RF switch and also for detecting X-rays and gamma rays.

  • Gunn diode - used to generate signals in the microwave range.

  • Crystal diode

  • Laser diode - used in optical devices; such as CDs, DVDs and Blu-ray recorders and players.

  • Light Emitting Diode (LED) - used in displays, as indicators and for lighting.

  • Photodiode - the inverse of the LED. Incoming light is converted to electrical current.

  • Tunnel diode - used as a very high-speed switch (in nanosecond range).

  • Peltier Diode - used in thermal applications for heating or cooling.

 

The list above is not exhaustive; however, it does serve to illustrate that diodes are widely used in many electronics applications. For many of these, there is a best state or operating point at which we want the diode to function. 

Determining the Operating Point of a Diode

Diodes are non-linear devices. As such, they have a non-linear characteristic I-V curve that describes their behavior. For diodes that operate forward-biased, this curve is positive and lies in the first quadrant of the typical Cartesian plane with voltage plotted along the x-axis and current along the y-axis. The characteristic curve is the well-known Schockley or diode equation, shown below.




Operating point of a diode equation for current and voltage

 

Diode operation can also be characterized by a load line, which is a line that extends through the points (ID, 0) and (0, VD). The point at which these two curves intersect is the diode operating point, more commonly referred to as the quiescent or Q point. 

As with any plot, the accuracy of the curves is dependent upon not only the calculations themselves but also the number of points plotted along the curves. This is not a concern for the load line as it is linear; however, this can be cumbersome for the I-V characteristic. For some diodes, there is not a single point but a range of operation and in many cases your circuit will contain several diodes. For these reasons, it is advisable to utilize an analysis tool to ensure accuracy and allow for more efficient circuit design. 

For fast accurate signal analysis that easily integrates with your board layout design, Cadence offers the most advanced PCB design and analysis software. This not only includes the most capable schematic capture, but also the SI/PI and analog/mixed signal simulation functionality of PSpice. 

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Layout Tips for Your DC DC Buck Converter Design
Layout Tips for Your DC DC Buck Converter Design

A good layout for a DC DC buck converter design on your printed circuit board is essential to its successfu...

Next Article
Working with MOSFET SPICE Models in Circuit Analyses
Working with MOSFET SPICE Models in Circuit Analyses

Here’s what you need to know about different MOSFET SPICE models in different circuit analyses.

Start My Free Trial Today

Start Now