Series RLC Circuit Design and Analysis in Your PCB

October 28, 2020 Cadence PCB Solutions

Key Takeaways

  • RLC circuits are fundamental in many applications involving low and high frequency signals.

  • Series RLC circuits and other RLC networks are useful models for describing parasitics behavior, impedance matching networks, PDN impedance, and many practical circuits.

  • Series RLC circuits are also common for modeling electrical behavior in a real layout in terms of parasitic circuit elements.

 Series RLC circuit PCB layout

Series RLC circuit behavior can arise in any layout, including this one.

Some circuits are fundamental for understanding electrical behavior of practical systems, including your PCB layout. In addition, some circuits appear in multiple applications, ranging from impedance matching networks to power supplies. A series RLC circuit is one such circuit you’ll find in circuit models, integrated circuits, and many other real circuits for practical applications.

Unlike other circuits found in digital and analog systems, series RLC circuits are important beyond real circuits you’ll find in a PCB layout. These circuits and larger circuit networks with RLC components find a home in modeling parasitics in many situations, the most prominent of which is modeling real capacitors and power delivery networks (PDN). Because the resonant behavior of these circuits is so important in many applications, we’ll look at how this behavior arises in real PCB layout and how it links back to fundamental properties of RLC circuits.

Series RLC Circuits

The image below shows a circuit diagram of an RLC circuit and its associated electrical behavior. The second-order differential equation describing the voltage distribution in the circuit is derived using Kirchoff’s laws.

Series RLC circuit and equations

Series RLC circuit and equations.

This circuit also exhibits a damped oscillation, where the response can be underdamped, overdamped, or critically damped. This occurs when the circuit transitions between states, i.e., when driven with an impulse or step function. The transient response can be easily calculated from the above equation and matches the transient response seen in a mechanical oscillator.

Finally, an underdamped series RLC circuit can exhibit resonance. If you calculate the total impedance in terms of Ohm’s law, you’ll find there is a particular frequency where the current in the circuit is maximized because the impedance is minimized. This then affects the power distribution throughout the circuit, and it’s worth comparing series and parallel circuits. The resonant frequency is:

Series RLC circuit and equations

Resonant frequency in a series RLC circuit.

Power Dissipation and Voltage Drop at Resonance

In the above circuit, power dissipation is purely reactive across the capacitor and inductive, while it is resistive across the resistor. At resonance, the inductor or capacitor are generating equal and opposite voltage, meaning their reactive power dissipation components cancel. Meanwhile, the resistor experiences maximum its power dissipation as the current in the resistor is maximum at resonance. The equation below summarizes the power dissipated in each component in a series RLC circuit.

Series RLC circuit power dissipation equations

Series RLC circuit power dissipation at resonance.

Series vs. Parallel RLC Circuits

In some ways, a parallel RLC circuit behaves in the opposite manner as a series RLC circuit. In particular, the parallel circuit has an anti-resonance, where the impedance is maximized rather than minimized. However, at anti-resonance, the same power dissipation is observed in both types of circuits. The parallel circuit is more commonly observed in RF applications as an amplifier circuit, oscillator, filter, or matching network, while the series version is more important in describing parasitics. In addition to parasitics, series RLC circuits are still used in many important areas.

Where Series RLC Circuit Behavior Occurs

Practical Circuits

A series RLC circuit may be present in an integrated circuit or on a PCB layout. Some practical areas in a PCB layout include:

  • Impedance matching networks for antennas. Here, the input impedance and bandwidth of the system are tuned by adjusting the appropriate R, L, and C values in the circuit. The goal is to match an antenna’s impedance to its feedline impedance.

  • RF bandpass filters. These circuits are configured to ensure a sourced voltage has maximum transmission through the circuit at resonance. These circuits are impedance matched at the input and output to the source and load components, respectively, to prevent reflections.

  • Relaxation oscillators. This type of oscillator takes advantage of the transient response of an RLC circuit to produce a sinusoidal output. When pulsed with a phase-matched low duty cycle signal, the oscillator can output a sinusoidal signal with very minor amplitude modulation.

  • Resonant LLC converters. This type of converter uses an LC circuit with low series parasitic resistance to provide resonance at the converter’s switching frequency. This provides maximum output current within a narrow regulation bandwidth, which allows the power supply output to be carefully regulated by adjusting the duty cycle of a driving PWM signal. 

Although these applications are most likely to be familiar to many designers, there are many other areas where series RLC behavior occurs. This behavior arises in other portions of an integrated circuit or PCB layout due to parasitics in the system. These unintentional circuit elements play desirable and undesirable roles in electrical behavior, depending on the frequency range and application.

Parasitics

Parasitic elements are not real circuits, but the language and concepts of RLC circuits are normally used to help describe the behavior of signals that interact with parasitics in real circuits and PCB layouts. In today’s advanced PCB designs, series RLC circuit behavior and resonances arise in two principle areas:

  • High frequency response of real capacitors. A real capacitor has some equivalent series inductance (ESL) and equivalent series resistance (ESR), so a real capacitor is a series RLC circuit. For this reason, real capacitors have a self-resonant frequency, which gives rise to resonances/anti-resonances in a PDN at intermediate frequencies.

  • Plane, package, and cavity resonances. This is another area of PDN modeling where resonances arise in a PCB at high frequencies (~100 MHz and above). These higher order resonances can also be modeled as arising in series RLC circuits.

When the above two areas are taken together, we can construct a standard model describing PDN impedance. This model places multiple series RLC circuits in parallel between the VRM output and the load component. This type of model can be examined with standard SPICE simulators and used to determine appropriate decoupling capacitor values to reduce supply rail collapse on a PDN.

PDN impedance with series RLC circuits

Model for PDN impedance in terms of series RLC circuit legs.

When your design software includes an integrated electromagnetic field solver, you can easily extract parasitic circuit elements in your layout. This can be done by direct calculation from the electromagnetic field from numeric field solver results. You can then incorporate these parasitic elements into your parallel and series RLC circuits as part of circuit design and optimization.

When you need to create circuits and models with series RLC circuit behavior and networks, you need to use the right PCB design and analysis software that includes schematic design and capture utilities. The design tools in Allegro PCB Designer from Cadence give you a complete set of PCB layout features with a full suite of analysis tools for post-layout simulation and parasitic extraction. Try this unique toolset when you need to design reliable PCBs for advanced applications.

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts.

 

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
How to Use Multiple Batteries in a Circuit: A Beginner's Guide
How to Use Multiple Batteries in a Circuit: A Beginner's Guide

There are various ways to use multiple batteries in a circuit depending on the desired outcome. Here is a g...

Next Article
Using Peak Current Flow to Optimize PCBA Layout
Using Peak Current Flow to Optimize PCBA Layout

Knowing the peak current flows on your board will allow you to optimize the design, as we describe in this ...

Start My Free Trial Today

Start Now