Key Takeaways

Nodal analysis in the frequency domain is meant to generalize DC and harmonic mesh and node analysis techniques into the frequency domain.

Working in the frequency domain is quite important for wideband signals with generalized impedance functions.

In addition to the frequency domain, designers can use impulse response functions in nodal analysis to work with nonharmonic sources in the time domain.
You can simulate the same waveform you might measure with an oscilloscope using nodal analysis in the frequency domain.
Among the various ways to analyze circuits by hand, nodal analysis gives you a simple way to examine the current and voltage distribution in DC circuits. It also works well for simpler AC circuits driven with harmonic sources. However, once we look at broadband sources and general impedance functions, can we still work in the time domain?
As it turns out, it’s much easier to set up problems involving general impedances and broadband voltage/current sources in the frequency domain. By constructing a matrix equation from Kirchhoff’s laws and Ohm’s law, you can derive a functional representation of the current and voltage at different locations in a circuit. DC techniques can easily be used to set up these problems, which we’ll show in a few examples.
Why Do Nodal Analysis in the Frequency Domain?
Nodal analysis is normally performed in the time domain for harmonic AC circuits or purely DC circuits. There are two particular reasons nodal analysis is normally discussed for these systems:

Fixed impedance: Nodal analysis in the time domain is generally limited to harmonic sources and impedances that are not functions of frequency. If there is one source, then all impedances will have fixed values. If there is more than one source, the impedances are assumed the same for both sources or the designer needs to determine what each impedance will be, which might lead to an incorrect guess.

Use DC node techniques: This gives the designer a simple way to calculate the voltage at every node in the system. Using Kirchhoff’s laws at each node in a circuit, the designer can derive a matrix equation for the system, which is then immediately solvable as long as the characteristic matrix is nonsingular.
Because timedomain nodal analysis is limited to harmonic sources with fixed frequencyindependent impedances, the results do not reflect a broad range of possible circuits. Almost all circuits do not exhibit flat impedance except in limited bandwidths. For simple circuits with harmonic sources at similar frequencies, the results from harmonic nodal analysis are realistic, but this is not the case with wideband sources and general impedance functions.
This is why it’s better to do nodal analysis in the frequency domain when working with broadband sources in your circuits. This simple technique allows DC nodal analysis methods to be used to solve circuit design problems with general impedances and wideband sources. The downside is that the problem constructed in the frequency domain must be all analytical or allnumerical, ultimately requiring a set of Fourier transforms to get back to the time domain.
Theory of Nodal Analysis in the Frequency Domain
Getting started with nodal analysis in the frequency domain follows the same steps one would follow in the time domain. In short, we want to determine the voltage and current at each point in a circuit using Kirchhoff’s laws, but we leave the impedance of each circuit element as a function of frequency. Because impedance is already defined as a function in the frequency domain, you can easily derive the following matrix equation:
Eq. (1): Characteristic matrix equation for nodal analysis in the frequency domain.
This equation relates the voltage at each node (numbered A to n on the lefthand side) to the various sources in the circuit. The sources are defined in the frequency domain by taking the Fourier transform of a timedomain voltage or current source. In other words, this formalism allows any input source in the time domain to be used in the nodal analysis as long as the impedances in the frequency domain are known. By taking the inverse matrix, followed by an inverse Fourier transform, we know the voltage at each node in the time domain:
Eq. (2): Voltage at each node in the time domain found by solving the characteristic equation shown in Eq. (1).
This gives you back the timedomain solution to the problem at each node in the circuit, which is exactly what we want. Unfortunately, the method shown above is not guaranteed to produce causal results as the Fourier transform of your system will likely need to be bandlimited. This is due to the fact that the inverse Fourier transform defined in Eq. (2) may not have a closedform integral and would need to be calculated numerically. An alternative method for getting the solution is to work in the time domain directly with impulse response functions.
Beyond Harmonic Sources in Nodal Analysis
Instead of working with nodal analysis in the frequency domain, you can work with arbitrary sources in the time domain using the procedure shown in this section. Your voltage sources can be rather complex functions of time, such as modulated or multilevel bit streams, pulses, and nonsinusoidal periodic functions.
If you know the impedance of each element in the circuit you’re analyzing, you can convert the impedance into an impulse response function by taking the inverse Fourier transform of the element’s impedance function. You can then formulate the system’s characteristic matrix equation in the same way you would in the frequency domain, which is analogous to Eq. (2) shown above. By taking the inverse, we have the following equation:
Eq. (3): Voltage at each node in the time domain.
This definition in terms of impulse responses and convolutions can be used to define a closedform convolution integral for the voltage at each node:
Eq. (4): Solution to the voltage at a node in terms of source voltages and elements of the inverse impulse response matrix.
Note that the above definition has a causal correction, where the inverse impulse response matrix element Fij1 is truncated at t = 0. This gives the following process for solving nodal analysis problems for any input and impedance function:

Calculate the characteristic matrix in the frequency domain shown in Eq. (1).

Calculate the inverse Fourier transform of each matrix element in Step 1 to get the matrix equation shown in Eq. (3).

Calculate the elements of the inverse matrix found in Step 2.

Plug the relevant elements into Eq. (4) along with the input voltage sources in the time domain to calculate the response voltage at each node in the time domain.
This procedure is a bit complicated to do by hand, but it provides analytical solutions for nontrivial circuits with known impedance functions.
The easiest way to perform nodal analysis in the frequency domain is to use the frequency sweep features in the frontend design software from Cadence. The PSpice Simulator application lets you create and simulate your circuits in the time domain and frequency domain, and you can perform a range of analyses using builtin functionality. Once you’ve designed your circuits, you can capture your circuits and start creating a PCB layout.
If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts.
About the Author
Follow on Linkedin Visit Website More Content by Cadence PCB Solutions