Understanding Resonant Angular Frequency in RLC Circuits

January 11, 2021 Cadence PCB Solutions

Key Takeaways

  • Understand what resonant angular frequency is.

  • Learn how to calculate resonant angular frequency.

  • Find out how bandwidth and Q-factor of resonant angular frequency relate to each other.

Illustration of silhouettes of people taking selfies

The angle matters when you’re taking a selfie, and the same goes for the importance of resonant angular frequency when designing an RLC circuit.

My lack of skills for taking selfies has often subjected me to ridicule. I could have the latest smartphone with a high-res camera and advanced filter apps, but every single image capture was still mediocre at best. Then, I discovered the magic word for taking better selfies—angle.  Apparently, you’ll get the best results when you take the snapshot at certain angles.

Thanks to that tip, I no longer take embarrassing selfies. It’s amazing how changing the angle could make a huge difference in the photos. In fact, it reminds me of how resonant angular frequency results in the shift of various parameters in an RLC circuit.  

What Is Resonant Angular Frequency? 

RLC series plot showing resonant angular frequency at its peak.

Current is at its peak resonant angular frequency.

If your PCB design consists of a series RLC circuit, you ought to understand the resonant angular frequency, as it is the pillar of applications that are derived from the RLC circuit. But first, let’s take a look at elements present in an RLC circuit.

An RLC circuit has a resistor, inductor, and capacitor. It is meant to be driven by an AC source. At different frequencies, the properties of the inductor and capacitor vary. Inductive reactance is calculated by XL = 2πfL, while capacitive reactance is given by Xc= 1/2πfC. Both XL and XL are determined by the frequency F. 

The term angular frequency is a measurement of the rate of change of the waveform per unit of time. It is measured in rad/s and is represented by the symbol ω. The angular frequency has a formula of ω = 2πf. 

Resonant angular frequency refers to a condition in which both XL and Xc become equal in amplitude at a particular frequency. Inductive reactance and capacitive reactance are 180° apart in-phase and cancel out each other at resonant angular frequency. So, the total impedance of an RLC circuit at the resonant frequency is given by Z = R, which means the circuit becomes purely resistive. 

Calculating Resonant Angular Frequency

RLC circuit analysis

At resonant frequency, capacitive and inductive reactance are of equal amplitude but opposite phase.

If the angle is pivotal in taking selfies, deriving resonant angular frequency is all about remembering that capacitive and inductive reactance is of equal amplitude but opposite phase. The relationship between both parameters is expressed in this equation.

XL = XC

Or 

2πfL = 1/2πfC

Replacing ω = 2πf to the equation gives:

ωL = 1/ωC. 

ω2 = 1/LC

The resonant angular frequency is obtained by further simplifying the equation as follows:

ω = 1/√LC

From the equation, it’s obvious that resonant frequency is solely dependent on the capacitor and inductor value. Changing or adding resistance to the circuit does not affect the angular resonant frequency. 

When an AC source with the value calculated by the above equation is applied, the series RLC circuit operates at resonance. At resonance, the inductor and capacitor equate to a short circuit. Therefore, the total impedance is at its minimum and current flow is at its peak. 

The RLC circuit and its ability to operate at resonance have found its way in various applications. A bandpass filter operates on the principle of resonance frequency, to allow signals at a selected frequency to pass through while attenuating others on the higher and lower range. The same principle is also used in TV receivers and smartphones.

When the LC element is configured in parallel, it can be used as a tanked circuit to stabilize an oscillator circuit. By operating in resonance, impedance is kept at a minimum, and energy transfer is at its maximum. 

Bandwidth and Q-Factor of Resonant Angular Frequency

An image illustrating bandwidth

Resonant angular frequency bandwidth varies according to Q-factor.

Besides determining the angular frequency, there are a couple of parameters that are important in designing and analyzing an RLC circuit. The bandwidth, which is measured between two points of -3 dB drop of the maximum amplitude, indicates the range of frequencies that are allowed to pass through.

The bandwidth can be narrow or wide, and it depends on the Q-factor of the circuit. The Q-factor is inversely proportional to the bandwidth. A higher Q-factor results in a narrower bandwidth and vice versa. 

Calculating the resonant angular frequency and creating an RLC circuit can be easily done with the right PCB design software. Allegro PCB Editor’s extensive component library and intuitive interface will help you lay out an RLC circuit in no time, while the Allegro PSpice System Designer is capable of simulating resonant angular frequency and providing an accurate analysis.

 

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

 

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
AC Voltage: A Beginner’s Guide
AC Voltage: A Beginner’s Guide

AC voltage is more complicated to understand than DC voltage. Check out this beginner’s guide to get a fir...

Next Article
Schmitt Trigger Hysteresis Provides Noise-free Switching and Output
Schmitt Trigger Hysteresis Provides Noise-free Switching and Output

Schmitt trigger hysteresis is easy to incorporate with standard op-amp models in your circuit design tools.

Start My Free Trial Today

Start Now