What is Nodal Analysis in Circuit Design?

January 14, 2021 Cadence PCB Solutions

Key Takeaways

  • Nodal analysis is a mathematical method that is used to analyze circuits in terms of voltage drops between nodes in a circuit diagram.

  • Nodal analysis can be performed in the time domain or frequency domain, but it is limited to linear time-invariant (LTI) systems.

  • Although the solution algorithm used in nodal analysis is only defined for linear systems, nonlinear systems can be approximated around an operating point and used in nodal analysis.

Circuit measurements nodal analysis

Circuit simulation results need to be compared with in-situ measurements during prototyping and production.

Analyzing electrical circuits is vital to ensuring modern technology works as expected. Most modern electronics go through some sort of simulation and evaluation process to ensure designs work as intended, and to provide a set of reference calculations for comparison with in-circuit tests. SPICE simulations are the workhorses for circuit design and analysis, and today’s commercial solutions provide many built-in simulations.

Among the simulations found in SPICE simulators, nodal analysis is a fundamental technique used to examine voltage and current distribution in a circuit. This technique effectively combines both of Kirchhoff’s laws and Ohm’s law into a single matrix equation. Keep reading to learn more about what nodal analysis is and how it’s used in circuit design and analysis.

What is Nodal Analysis?

Nodal analysis is a mathematical method for calculating the distribution of voltages between nodes in a circuit. Also referred to as the node-voltage method, this strategy uses Ohm’s law, Kirchhoff’s voltage law, and Kirchhoff’s current law to define an equation relating the voltage measured between each circuit node and some reference (usually ground). The voltage drops measured between neighboring nodes are taken as the variables in a set of linear equations and the system can be solved using a standard algorithm (e.g., Gauss-Jordan elimination).

Constructing a Matrix Equation in Nodal Analysis

The general process for constructing a matrix equation for nodal analysis is to use Kirchoff’s laws between each node in a circuit diagram to write out a set of equations relating the voltage drop across different components to the currents flowing into each node. Use the following process:

  1. Draw out the circuit diagram with currents defined at each node.

  2. Pick a reference node (usually ground) and write a variable for the voltage at each node with respect to the reference node.

  3. Write out Kirchoff’s current law for each node in terms of the circuit impedances and the voltages at neighboring nodes.

  4. Rewrite the system of equations for the node voltages in matrix form.

  5. Solve the matrix equation using an inverse matrix.

To see how this works, it helps to look at a simple example.

An Example of Nodal Analysis

The example circuit diagram below shows 4 impedances with 1 voltage source and 4 distinct nodes. Node A is just the input voltage, leaving the voltages at the 3 other nodes to be determined. By applying steps 1-3, we arrive at the following set of equations for the voltages at each node:

Nodal analysis example

The circuit diagram and the system of equations used to determine the voltages at each node.

We can then rewrite the above 3 equations as a matrix equation:

Nodal analysis example

Rewriting the circuit diagram’s system of equations as a matrix equation.

This matrix equation is then easily solved by multiplying by the inverse of the coefficient matrix. In the above circuit diagram, we’ve defined a “reference node” at the common ground connection. The voltage variables are all measured with respect to this point. This is important for more than just creating a closed circuit; it sets the measurement reference for all voltage variables that appear in the above matrix equation.

Reference Nodes

One key to doing nodal analysis successfully is to properly define reference nodes, also called datum nodes. In nodal analysis, a reference node is the point that is used for comparison when measuring voltages, because a voltage is only defined between two points in space. Imagine you were using a voltmeter on your circuit diagram; the reference node would be the point where the negative lead was connected, and the positive lead would connect to any other node. This is why voltage measurement probes in SPICE simulations are normally shown as a single probe; the measured voltage is taken with respect to a reference node in the circuit.

Circuit simulation results

In this PSpice simulation result, the voltage measured at this probe is just the voltage measured between R4 and GND; this is determined using nodal analysis.

In SPICE simulations, the reference node is normally taken as ground. If there are two grounds, the reference node is taken as the nearest connected ground potential. In nodal analysis, any node can be taken as a reference point. This gives you an advantage in that you can define a potential difference between two different ground points, such as you might find in a galvanically isolated PCB with two different ground planes.

How Does Nodal Analysis Work on Nonlinear Circuits?

Because the current and voltage in a nonlinear component is a nonlinear function (meaning the relationship does not obey Ohm’s law), the matrix equation developed in nodal analysis will have terms that are functions of the voltages at different nodes.

Nonlinear impedance matrix

The solved voltage column vector in this equation is defined in terms of a nonlinear impedance matrix and the current in each portion of the circuit. This transcendental matrix equation may include coupled terms, which require simultaneous iterative numerical techniques to determine solutions.

In this general formulation, applying nodal analysis to nonlinear circuits requires solving a transcendental matrix equation for multiple unknowns. This can be a very difficult numerical problem to solve, depending on the form of the derived matrix equation.

Therefore, in order to examine nonlinear circuits using nodal analysis, the current vs. voltage relationship measured between adjacent nodes in the circuit needs to be approximated around some operating point. The typical method to do this is to use one of the following general approximation techniques for a nonlinear time-invariant system:

  • Taylor series: For a system of N components, define 2N new variables that are shifted away from the intended operating point with a linear transformation. Now, expand the current-voltage function for each nonlinear component as a Taylor series in terms of these new variables.

  • Maclaurin series: Expand the current-voltage function for each nonlinear component directly around the operating point without defining new variables as a Maclaurin series.

By keeping only the first-order terms (i.e., linear terms), you now have a linearized circuit that includes nonlinear components. The results from this procedure are only valid within a small deviation from the operating point, depending on the impedance function for each nonlinear component in the system. Circuit simulators that use iterative solution techniques will apply these approximations for you and can solve operating point matrix equations in nodal analysis for nonlinear circuits.

If you’re still unclear as to what nodal analysis is, you can use an industry-standard SPICE simulator to calculate voltage and current throughout your circuits. Once you’ve got your results and you’re ready to create your physical design, use the best set of PCB design and analysis software to capture your schematics as a blank circuit board. Allegro PCB Editor from Cadence gives you the layout and routing features you need to create your circuit boards and prepare them for production. You can then use nodal analysis results as a comparison for electrical tests.

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

 

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
How and Why to Convert Analog Signals  to PWM Signals
How and Why to Convert Analog Signals to PWM Signals

Check out this article for how to convert analog signals to PWM signals, as well as some design tips for an...

Next Article
AC Voltage: A Beginner’s Guide
AC Voltage: A Beginner’s Guide

AC voltage is more complicated to understand than DC voltage. Check out this beginner’s guide to get a fir...

Start My Free Trial Today

Start Now